
Bathroom lighting
Backlit bathroom mirrors
A backlit bathroom mirror is a light fixture first. In Ontario it must carry a recognized certification mark such as CSA, cUL or cETL and be suitable for a damp location, and a hardwired model is connected to a junction box and wall switch, work that a hired electrician must do as a Licensed Electrical Contractor under an ESA notification. For the light itself, NKBA guidance calls for at least 90 CRI, a colour temperature between 2700K and 5000K, dimming, and about 50 foot-candles on the face.
Check the certification mark before anything else
Ontario's Electrical Safety Authority (ESA) is direct about this: before an electrical product is used, sold, displayed or advertised for sale in Ontario, it must be approved by an accredited certification or evaluation agency and carry that agency's mark, and installing or connecting unapproved equipment is against the law. ESA's list of recognized marks runs to more than 20 agencies, including CSA, Underwriters Laboratories, Intertek and QAI.
That is the catch with mirrors bought online or shipped from overseas. ESA advises buyers to look for a recognized Canadian mark and to ask the seller when the listing does not state one. A product that arrives without a mark can sometimes be approved afterwards through a field evaluation by an agency ESA recognizes, but buying a certified model is far simpler.
Damp ratings, distance from water and the mirror glass
A vanity wall gets steam and condensation rather than direct spray, so the usual requirement is a fixture suitable for damp locations, which lighted-mirror makers state on their specification sheets. NKBA's lighting guidance adds that lighting above a tub or inside a shower compartment should be rated for damp locations, that decorative and surface-mounted fixtures should not go inside a shower compartment, and that they should not sit within 36 inches horizontally of a tub's edge and 96 inches above its rim. A vanity tucked beside a tub can fall inside that zone, so check the layout early.
The glass matters as much as the LEDs. Moisture and harsh cleaners attack a mirror's silvered backing from the edges, which is why some makers use corrosion-resistant mirror glass tested in salt-spray (CASS) chambers, and why Electric Mirror, a lighted-mirror maker, voids its glass warranty if ammonia-based or corrosive cleaners are used or the edges and back are not kept dry.
Hardwiring needs a box, a switch, studs and a notification
Many backlit mirrors are made to be hardwired. A typical specification, Electric Mirror's for its frame-lit vanity mirror, calls for a 120-volt hardwired connection to a junction box controlled by a wall switch supplied by others, with the mirror fixed to the wall studs on a supplied cleat. So the box has to be roughed in at the right height and position behind the mirror before the wall is closed, with blocking where the mounting screws land.
In Ontario, anyone you hire for electrical work in your home must be a Licensed Electrical Contractor (LEC). ESA explains that the contractor files the notification, has the work reviewed and receives a Certificate of Acceptance, a document your insurer may ask for and that can matter when you sell. ESA also notes that most electrical work requires a notification, including work homeowners do themselves.
Settle the dimmer at the same time. Mirror drivers are built for a particular dimming method, such as line-voltage phase (triac) dimming or 0-10 volt control, and the wall dimmer has to match; Electric Mirror's installation guide marks the method in the part number on the mirror's label.
Colour temperature, CRI and brightness that flatter a face
NKBA's guidance for mirrors with integrated lighting is specific: the fixture should be dimmable, should not interfere with the faucet or accessories, and should deliver at least 50 foot-candles (538 lux) to the user's face. Its room-wide rules ask for 90 CRI or higher, a colour temperature between 2700K and 5000K chosen for the user and the finishes, and one consistent colour temperature across the room.
| Specification | What to look for | Why it matters |
|---|---|---|
| Certification | CSA, cUL, cETL or another ESA-recognized mark | Required to sell, install or use it in Ontario |
| Location rating | Suitable for damp locations | Steam and condensation at the vanity |
| Colour rendering (CRI) | 90 or higher | Skin tones and makeup look true |
| Colour temperature | 2700K to 5000K; 3000K is a common default | Warm reads relaxed, cool reads crisp; match the other lights |
| Light on the face | At least 50 fc (538 lux) | Enough for shaving and makeup |
| Control | Dimmable, with a driver matched to the wall dimmer | Bright for grooming, low at night |
A mirror is task light, not room light
Electric Mirror ships 3000K as its standard because, in its words, a bright, warm colour is generally most flattering, and some models offer tunable white so you can move between warm and cool. Keep the ceiling lights at the same colour temperature or the room looks patchy. NKBA still calls for general lighting of at least 20 foot-candles across the room, which bathroom lighting design covers.
The herringbone bathroom in High Park shows the effect: a backlit mirror over a navy double vanity, with slab surfaces and brushed gold fixtures picking up its glow.
Defoggers and day-to-day care
A defogger is a heating element behind the glass that keeps part of the mirror clear after a shower, usually an option wired with the lights; fog-free bathroom mirrors explains how they work, and a properly sized exhaust fan helps the whole room.
Clean a lighted mirror with warm water on a microfibre cloth. Electric Mirror's care instructions rule out acid- or alkali-based cleaners and anything containing ammonia, bleach or vinegar; if you use a cleaner at all, it should be free of ammonia and bleach with a pH below 8. Apply it to the cloth, never spray the mirror, and dry the edges and joints so nothing seeps behind the glass. That is the opposite of the diluted-vinegar routine some makers allow on shower glass, so keep a separate cloth for the mirror; how to keep a glass shower clean covers the glass.
Questions
Can I install a backlit mirror myself in Ontario?
A plug-in model needs no new wiring. A hardwired one does, and ESA says most electrical work needs a notification, including a homeowner's own work in their home. If you hire anyone to do it, they must be a Licensed Electrical Contractor who files the notification.
Will a backlit mirror light the whole bathroom?
No. It is task lighting for the face. NKBA calls for at least 20 foot-candles of general light in the room as well, from ceiling fixtures or other sources set to the same colour temperature as the mirror.
Why are the edges of my old mirror turning black?
That is the silver backing corroding, usually from moisture and cleaners reaching the edges. It does not recover, so the fix is a new mirror. Dry the edges after cleaning, avoid ammonia and vinegar near them, and look for corrosion-resistant mirror glass next time.
Sources and further reading
- Electrical Safety Authority: Recognized approval marks
- Electrical Safety Authority: Hire a Licensed Electrical Contractor
- NKBA Kitchen & Bath Planning Guidelines, 4th edition (summary, lighting planning)
- Electric Mirror: Brilliance frame-lit vanity mirror specification sheet
- Electric Mirror: Mirror care and cleaning instructions
Checked November 19, 2026. Codes, by-laws, prices and product specifications change; confirm with your municipality, condo corporation or supplier before you build.
Keep reading
Related guides


