Renovations

Guides

Walk-in shower in dark marble-look tile with a black rain head, niche and blue arabesque tile wall

Renovation design

The renovation design process, from measurements to drawings

A renovation design starts with measuring the room as it is actually built, turns that into an existing-conditions plan, tests layout options, and ends with a drawing set: floor plan, wall elevations, an electrical and lighting plan, and plumbing locations, with every selection attached. Once you approve it, those drawings drive cabinet shop drawings, orders and, where needed, permit drawings. At Purple Kitchen & Bath this is stage two of four, design and planning, and it ends with layout, selections, approvals and permits planned before work begins.

By the Purple Kitchen & Bath team · Updated · 4 min read · Photo: a Purple Properties project

Design is the second of four stages, and the one the build follows

Purple Kitchen & Bath runs every project through four stages: a consultation with Rowan Henry and the design team about the space, goals, style and budget; design and planning; the build; and a final walkthrough. The design stage is where a wish list becomes instructions a crew can build from without guessing.

If you already work with a designer, the same drawings can come from them; Purple Kitchen & Bath can work alongside a homeowner's own designer. Design-build renovation explained and working with a kitchen designer and a contractor compare the two arrangements.

What gets measured on the site visit, and why

A design is only as good as the measurements under it, and in older GTA houses walls are rarely straight, square or plumb. A good site measure records the room as built, not as it appears on an old floor plan or a listing sheet.

Site measurements and what each one decides
MeasuredWhy it matters
Wall lengths at floor, counter and ceiling heightWalls bow and lean; cabinet runs and tile layouts must fit the tightest point
Corners checked for squareOut-of-square corners show up in countertop joints and tile lines
Ceiling height, bulkheads and soffitsSets upper cabinet height, crown details and whether a fan duct can run above
Windows and doors: openings, trim widths, sill heightsA low sill limits the backsplash; trim widths eat into cabinet runs
Floor level across the roomCabinets are levelled to the high point; a curbless shower needs the floor depth
Drain stack, vents, supply, gas line and ductsShows what can move easily and what is expensive to relocate
Joist direction and depth, seen from belowDecides whether a toilet or sink drain can run where you want it
Electrical panel size and spare spaceTells the designer whether new circuits fit or a panel upgrade belongs in the plan

From measurements to a layout you can choose

The measurements become an existing-conditions plan: the room as it stands, with every pipe, vent and receptacle located. Layout options are drawn on top of it, usually two or three, each tested against working clearances, appliance and fixture specifications, and the routes the plumbing and ducts would need.

This is the stage to bring references. Photos of rooms you like, and notes on what you dislike about the current room, help the designer narrow the options quickly; moodboards and design references shows how to collect them. Once a layout is picked, everything that follows is drawn to that version, so changing it later means redrawing every sheet that depends on it.

The drawing set, sheet by sheet

A kitchen or bathroom drawing set is several drawings that each answer a different trade's questions. Ask to see all of them before you sign off, not only the renderings.

What a renovation drawing set usually contains
DrawingWhat it showsWho builds from it
Floor planWalls, cabinets or fixtures, appliances, clearances and dimensionsEveryone; it is the master sheet
Wall elevationsEach wall face-on: cabinet sizes, shelf and appliance heights, tile extents, niche and valve heightsCabinet maker, tile setter, plumber
Electrical and lighting planReceptacles, switches, pot lights, pendants, under-cabinet lights, fan and dedicated circuitsElectrician
Plumbing locationsDrain, supply and vent positions for each fixture, with rough-in heightsPlumber
RenderingsHow the finished room will look in colour and lightYou; trades don't build from them
Cabinet shop drawingsThe cabinet maker's own drawings of every box, door and fillerCabinet shop, after your approval
Permit drawingsCode-focused plans and sections, when the work needs a permitToronto Building and its inspectors

Permit drawings in Toronto follow their own rules

When a renovation moves walls, opens new windows or changes plumbing, the design drawings feed a permit set, and Toronto's interior alterations guide spells out what that set needs. Drawings go on standardized sheets, drawn to scale, fully dimensioned, signed and dated, submitted as PDF files, and without personal information such as the owner's name or phone number.

Floor plans must show existing and proposed uses of every space, the locations of smoke alarms and carbon monoxide detectors, all plumbing fixtures, and the structural framing above. A Schedule 1 Designer Information Form is required for every designer other than engineers and architects, and drawings by a qualified designer carry the designer's name, registration and qualification numbers, signature and a stamp or statement accepting responsibility. Engineer-sealed drawings also need the City's Assumption of Responsibility for Engineering Content form.

Keep the stamped permit plans on site: Toronto asks for them at inspections. Whether your project needs a permit at all is covered in the kitchen permit guide and the bathroom permit guide.

Selections and sign-offs lock the design

Drawings are only final when the products on them are. Each selection, from the faucet to the tile edge trim, should be listed against the drawing it affects, with model numbers, finishes and quantities. Choosing renovation finishes without delays explains which ones must be settled first.

Approve each revision in writing and keep the latest set in one place, because a crew building from an old version is one of the costliest mistakes a renovation can make.

  • Homeowner sign-off on the final drawings and selection list.
  • Cabinet shop drawings checked against the elevations before production starts.
  • Permit issued where the work needs one.
  • ESA notification filed by whoever does the electrical work, before that work starts.
  • Condo approval where the building requires it; see getting condo board approval.

Questions

Can I bring drawings from my own designer?

Yes. Purple Kitchen & Bath can work alongside a homeowner's designer. If the project needs a Toronto permit, the permit drawings still need the designer information Toronto requires, so check who is preparing them.

Do I need an engineer for a kitchen or bathroom design?

Usually only when the design touches structure, such as removing a load-bearing wall or cutting a large new opening, and the beam or framing falls outside what a qualified designer can size. When an engineer seals the drawings, Toronto also needs its Assumption of Responsibility for Engineering Content form.

What's the difference between a rendering and a construction drawing?

A rendering shows how the room will look; a construction drawing tells a trade exactly where and how big things are. Approve the renderings for style, and check the elevations and plans for heights, sizes and locations.

Can a homeowner prepare their own permit drawings in Toronto?

Toronto's guide allows for property owners who are exempt from the designer qualification requirement; they state the reason for the exemption on Schedule 1. The drawings must still meet the same content rules as any other set.

Sources and further reading

  1. Interior alterations: application guide (City of Toronto)
  2. When to call for inspection of small buildings (City of Toronto)
  3. Notifications and inspections (Electrical Safety Authority)

Checked November 19, 2026. Codes, by-laws, prices and product specifications change; confirm with your municipality, condo corporation or supplier before you build.

Plan your kitchen renovation

Initial consultations are complimentary. Jordan Duda, our client care and lead estimator, is usually your first point of contact.